1963 ford thunderbird fuel filter location

#1963 FORD THUNDERBIRD FUEL FILTER LOCATION INSTALL#
#1963 FORD THUNDERBIRD FUEL FILTER LOCATION PROFESSIONAL#
#1963 FORD THUNDERBIRD FUEL FILTER LOCATION FREE#

#1963 FORD THUNDERBIRD FUEL FILTER LOCATION INSTALL#

Install the fuel filter and bracket on the frame.ġ3. Pull on the fitting to make sure it is fully engaged.ġ1. Align the fitting, and filter axially and push the fitting onto the filter end. Hello, I have included the information that you requested down below in the diagrams. Classic Industries offers a wide selection of Fuel System Components for your 1963 Ford Thunderbird.

#1963 FORD THUNDERBIRD FUEL FILTER LOCATION FREE#

Inspect the inside of the fitting to make sure it is free of dirt and/or obstructionsġ0. 1963 Ford Thunderbird Parts - Fuel System. Thunderbird (55-79) PART : 66-33834-1 1961-1962 Ford Thunderbird Door Trim Panels, White, Vinyl Covered, No Armrests To Early 1962 924. Before installing the fitting on the filter, wipe the filter end with a clean cloth. Once installed pull on both ends of each connection to make sure they are secure.ĩ. Should also apply to Tbird 430MEL Engines. Push the connectors together to cause the retaining tabs to snap into place. Cylinder head bolts, freeze plugs, flywheel bolts, main bolts, rod bolts, stainless steel engine fastener kits and more. Install the new plastic connector retainers onto the filter inlet and outlet tubes (plastic collar type fittings).Ĩ. Install the fuel filter so that the flow arrow follows the direction of fuel flow.ħ. Remove the protective caps from the new filter and apply a few drops of clean engine oil to both tube ends of the filter and O-rings. Insert the tool into the female side of the connector, then push inward to release locking tabs. This is available from your local parts store.ī. I have had no issues with fuel being drawn to the carburetor. The filter attaches to the top inside nipple along with a black rubber gasket. PLEASE NOTE: As of Augour Windsor location will no longer be open for Walk-In Traffic Vehicle Fitment: The Vehicle Fitment Guide is to be used. Use a fuel pipe quick-connect separator J37088 or equivalent. There is no spring to hold up the filter. Squeeze the plastic retainer release tabs and pull the connection apart. Buy now from K&Ns Online Store and get a 100 money back guarantee on any Ford Thunderbird air filter Designed to Increase Horsepower and Acceleration High. Repeat for the other fuel line fitting.ī. Twist the quick connect fitting 1 / 4 turn in each direction to loosen any dirt within the fitting.

Grasp the filter and one fuel line fitting.

The pressure must be relieved before servicing these fuel systems.ġ. Ive replaced the spark plugs, good battery, new fuel pump, rebuilt the starter and now Id like to check the fuel filter but I am having a hay day trying to find it. When it is time to replace or repair your carburetor, a carburetor kit from OReilly Auto Parts has all the common parts you might need to rebuild your carburetor. Gasoline vapors are EXTREMELY volatile!įuel supply lines on all vehicles equipped with fuel injected engines will remain pressurized for long periods after engine shutdown. 78THUNDERBIRD351 MEMBER 1978 FORD THUNDERBIRD 150,000 MILES My car is having a hard time starting.

#1963 FORD THUNDERBIRD FUEL FILTER LOCATION PROFESSIONAL#

Always refer to a professional to verify correct fitment for your vehicle.Never smoke when working around gasoline! Avoid all sources of sparks or ignition. The data has been provided by our suppliers and manufacturers and may contain errors or incorrect data. The 390 was part of the Ford-Edsel (FE) engine family, which was produced from 1958 to 1976. The Ford 390 was a 6.4-liter (390.04ci) gasoline big block V8 engine that was produced between 19. The Vehicle Fitment Guide is to be used as a general reference. This article may contain affiliate links where we earn a commission from qualifying purchases.

1963 ford thunderbird fuel filter location